Trang Wiki hướng dẫn bạn cách thức tháo lắp bàn gia nhiệt của P1P

Bàn gia nhiệt (Heat bed)

Dụng cụ

Khóa lục giác H2.0/1.5

Nhíp kẹp

Chuẩn bị

Rút dây cáp nguồn máy in để sẵn sàng cho các bước tiếp theo.

Video hướng dẫn

Video hướng dẫn này dành cho việc lắp đặt bàn gia nhiệt của X1C V3. Tương tự X1C, thay thế bàn gia nhiệt P1P/P1S cũng được thực hiện tương tự. Vì thế, bạn cũng có thể tham khảo các bước thực hiện trong video này.

Disassembly

Step 1 – Remove the rear panel, excess chute, and the cable cover

Refer to the related contents of the Rear panel, Excess chute, and Cable cover to remove the rear panel, excess chute, and cable cover.

Step 2 – Disconnect the heat bed power cable

To remove the power cables, first, take off the protective rubber sleeve. Then, using tweezers, carefully release the locker and gently pull out the two power cables one at a time.

Step 3 – Disconnect the heat bed signal cable

To disconnect the cables, start by carefully unplugging the MC-AC connection cable. Then, remove the silicone glue on the heat bed signal cable and carefully disconnect the signal cable.

Step 4 – Remove the ground screw

To loosen the ground cable, first press down on the nut with your hand. Then, using an H2.0 hex key, carefully unscrew the ground screw to release the cable.

Step 5 – Release the cables

To remove the heat bed cables, carefully loosen them from the cable buckles/clips as shown in the image below.

Step 6 – Remove the cable mesh

To remove the cable mesh, carefully tear off the tapes at both ends of the mesh. 

Step 7 – Raise the heat bed

To prepare for the next steps, lay the printer on its right side and by pulling on the Z-axis belt to raise the heat bed to about 2/3 of its full height.

Step 8 – Remove the holding plate

Unscrew 2 screws and remove the holding plate.

Step 9 – Unlock the heat bed

To remove the heat bed, first return the printer to an upright position. Then, use the hex key to carefully loosen the six screws that hold the heat bed in place and lift it away from the printer.

Step 10 – Remove the heat bed

To remove the heat bed, lay it on its side as shown in the image below and gently pull out the heat bed cables. Then, carefully lift the heat bed away from the printer

Assembly

Step 1 – Installing the heat bed

To install the heat bed, first, place it on the 3 Z-sliders and then slide the heat bed as far forward as possible. Once it is in position, use the hex key to carefully tighten the six screws to hold it in place.

Step 2 – Pass through the heat bed cables, lock the holding plate

To install the printer, first, place it on its right side. Next, pass the heat bed cables through the cable hole on the rear slider. Make sure to arrange the cables and press them into the cable groove of the rear slider. Once the cables are in place, install the cable holding plate and secure it with two screws.

Step 3 – Install the cable mesh

Install the cable mesh onto the cables, securing the ends with tape.

Step 4 – Sort out the cables

To complete the installation, pass the ground cable through and position and secure the power cable and signal cable into the provided cable buckle/clip.

Step 5 – Secure the ground cable

To secure the ground cable proceed to carefully reinstall the cable with the provided screw and nut.

Step 6 – Connect the power cable

check the status of the power cable plugs. Once they are confirmed, connect both plugs to the AC board connector. Finally, mount the protective sleeve to complete the process.

Step 7 – Connect the signal cable

To connect the heat bed signal cable, attach it to the corresponding connector on the MC board. Then, apply silicone glue to the connector for added stability. Finally, connect the MC-AC connection cable to complete the process.

Step 8 – Install the cable cover, excess chute, and the rear panel

Refer to the related contents of the Cable cover, Excess chute, and  Rear panel to install the cable cover, the rear panel, and the excess chute.

How to verify

To finish the setup of the printer, connect the power cord cable. Then, turn on the printer and run the device self-test process. If the self-test is successful, the operation has been completed successfully.

2 Bình luận tại “Hướng dẫn lắp đặt bàn gia nhiệt”

Góp ý sửa bài